Welcome,
Shamu Advanced Material
Service line
86 0532-66739676
Polyurea Supporting Product
The Best Performance, The Best Service

Qtech-114 Aliphatic Polyurethane Top Coat


 

 

 

Qtech-114 Aliphatic Polyurethane Top Coat

PRODUCTION INFORMATION
 
Production Description
Qtech-114 is independently developed by Qingdao Shamu International Trade Co., Ltd. It is the state of the art heavy solids, flexible, spray-applied two components aliphatic polyurethane top finish coat, offering outstanding chemical, temperature, permeation, ultra color stability and ultraviolet light resistance. Qtech-114 is a superior coating material formulated specifically for industrial and commercial application receiving constant or intermittent exposure to ultraviolet light. Qtech-114 is designed for application in severe duty environments subject to chemical and ultraviolet light exposure.
 
Qtech-114 is the optimum choice where a tough, impact resistant, abrasion resistant, anti-corrosion, waterproof, weather resistant and decorative surfacing system which exhibits extraordinary performance characteristics.
 
Advantages
1.  Excellent resistance to ultraviolet light.
2.  Good weather ability, Added color stability.
3.  Excellent Physiochemical Properties.
4.  High tensile strength and elongation.
5.  Good adhesion to a wide range of substrates.
6.  Ambient insensitive, good thermal stability.
7.  Good resistance to a wide range of chemical attack.
8.  Anti-corrosion, Salt fog resistance, Abrasion resistant.
9.  Ecology friendly.
10.  No chalking and fading in long-term use outdoors.
 
Recommended Uses
•  High Grade Building Decorative.
•  Infrastructure Railway, Bridge, Subway Decorative.
•  Marine, Vehicle, Mechanical Equipment Decorative.
•  Aromatic Polyurea Weather Resistant Topcoat.
•  City Landscape.
 
Physical Properties

Tensile Strength/ MPa

≥4

Elongation/%

≥200

Flexural (ø10mm, ≤-30 ºC)

No Blister, No Cracking, No Spalling

Impact/(Height arm of fall, 100cm)

No Blister, No Cracking, No Spalling

Alkali Resistance/(NaOH 5% , 240h)

No Blister, No Cracking, No Spalling

Acid Resistance/(H2SO45%, 240h)

No Blister, No Cracking, No Spalling

Salt Tolerance/(NaCl 3%, 240h)

No Blister, No Cracking, No Spalling

Oil Resistance/(240h)

No Blister, No Cracking, No Spalling

Water Resistance/(48h)

No Blister, No Cracking, No Spalling

Artificial Weather Accelerated Test/(1500h)

No Blister, No Cracking, No Spalling

 
Product Characteristics

Solids/%

60

Fineness/μm

≤50

Tack Free Time/ (25 ºC, RH=60%, h)

≤4

Set Time/ h

≤24

Recommended Thickness/μm

60~80

Mix Ratio V/V

2: 1(Consult)

Colors

Optional

 
Drying time is temperature, humidity, and film thickness dependent.
 
 
ORDERING INFORMATION
 
Packaging
•  Part A: 100kilogram per drums.
•  Part B: 50 kilogram per drums.
( Custom package available at additional charge).
 
Freight Classification
Coating Solution Non-Flammable Liquid .
 
 
APPLICATION INFORMATION
 
Surface Preparation
Surface must be clean and sound. It may be free of standing water. Remove dust, laitance, grease, curing compounds, and other bond inhibiting contaminants.
 
Application Conditions
       Temperature:
            Air and surface: -20°C~40 °C.
            At least 3 °C above dew point.
        Relative humidity: ≤90%.
        Materials must be preheated to 21°C prior to use.
 
Mixing
Pre-mix each component thoroughly. Place 1 part by volume of component A and 1 part by volume of component B into a clean pail. Mix thoroughly for 3 minutes with low speed drill using agitator’s mixer until uniformly blended.
 
Storage and Transport
1.  The A component is affected by moisture and must be protected from moisture contamination. Containers are factory sealed with an inert gas to prevent contamination. Keep all containers tightly closed during storage. For further storage after opening, containers must be purged with nitrogen gas or dry air and tightly sealed to protect from moisture contamination.
2.   Store drums and pails in a cold, dry and ventilated location between 15°C and 40°C.
3.   Six months in sealed unopened containers.
4.   Keep away from fire and heat source.
5.   Keep away from rain and sun.
 
Safety
Read and understand the MSDS provided with all shipments. Always use products with adequate ventilation and use required PPE. For confined space use fresh air supply. For open air, use half face, twin cartridge respirators approved for MDI. Always protect eyes and skin. Strictly adhere to industry safety standards.
 
Availability
Because of the technical nature of the material and equipment required that will assure you of a professional installation, Qtech series products is available through a professional trained applicators by Qingdao Shamu International Trade Co., Ltd..
Notes
1.  Reading and understand the production information.
2.  This product is intended for industrial use by properly trained professional applicators only.
3.  Adding a nitrogen blanket is strongly recommended for use on the “A” component for storage after opening.
4.  The quality and fitness of the product is depending upon the proper mixture and application of the component by the applicator.
5.  This specification is an accumulation of long term testing and experience. Published technical data and instructions are subject to change without notice.
6.  For more information please consult the Qingdao Shamu International Trade Co., Ltd. or visit our website www.shamu-intl.com or www.polyurea.cn.
 
 
 
 
Technical Data Sheets

 •  Qtech-114 Aliphatic Polyurethane Top Coat  [2011-05-06]