Welcome,
Shamu Advanced Material
Service line
86 0532-66739676
Functional Polyurea
THE BEST PERFORMANCE, THE BEST SERVICE

Qtech-407 Anti-Microbial Polyurea Material


 

 

Qtech-407 Anti-Microbial Polyurea Material

PRODUCTION INFORMATION
 
Production Description
Qtech-407 Anti-Microbial Polyurea Material is the state of the art 100% solids, ultra fast cure, flexible, spray-applied, high build, and two components aromatic pure polyurea elastomer. The system consists of A component, a quasi-prepolymer rich of free NCO, and B component, a mixture of polyetheramines, amine extenders and other additives. Qtech-407 has been chemically engineered to inhibit the growth of a broad range of micro-organisms such as gram-negative and gram-positive bacteria, fungi and select viruses, so it will not wash or wear off or lose its biostatic properties after installation. Qtech-407 can produce an extremely tough film at all thicknesses; it may be applied in all positions and to any suitably prepared substrate. Qtech-407 is relatively moisture and temperature insensitive, allowing application in the most problematic ambient conditions. It is the optimum choice where a tough, flexible, anti –microbial surfacing system which exhibits extraordinary performance.
 
Advantages
1. Fast cure, short down time, no sagging.
2. Excellent Anti-microbial and Mildew Proof Properties.
3. Bondable and paintable to various kinds of substrates.
4. Ambient insensitive, good thermal stability.
5. 100% Solids, No VOC’s, Odorless, No Toxic Vapors.
6. Good resistance to a wide range of chemical attack.
7. High impact and abuse resistant-replaces fiberglass and FRP.
8. Good weather ability, Added color stability, no chalking.
9. Seamless, flexible, slick and non-porous.
10. Bridge moving cracks to 1/16’’.
 
Recommended Uses
Qtech-407 Anti-Microbial Polyurea Material is an ultra fast cure system; it can be applied at thicknesses of several ten millimeters, or greater, in a single application. It can be widely used in:
  • Clean Room Walls Ceilings and Floors
  • Food and Beverage Processing Areas
  • Pharmaceutical Facilities
  • Hospital and Research Facilities
  • Lavatories
  • Correctional Facilities
 

 
Physical Properties

Tensile Strength/ MPa

17.5

Elongation/%

400

Tear Strength/( N/mm)

55

Shore Hardness

A80

Abrasion Resistance /(GB/T 1689-1998, cm3/1.61km, mg)

≤0.35

Impact Strength/( Kg.cm)

20

Anti-Microbial Rate/%

99.9

Adhesion (Pull off, MPa)

≥2.5

Density/( g/cm3)

0.95~1.05

 
Product Characteristics

Solids/%

100

VOC (calculated)

0

Gel Time/s

11

Tack Free/s

20~30

Shelf Life

6 months, unopened at 15~40 ºC

Flash Point/ ºC

150

Mix Ratio V/V

1: 1

Recommended Spreading Thickness/mm

2~3

Colors

Optional

 
Drying time is temperature, humidity, and film thickness dependent.
 
Chemical Resistance
Consult our technicist and chemical test date for corrosive environment applications.
 
Installation
Consult our application information and recommended method statements.
 
Packaging
•  Part A: 220 kilogram per drums.
•  Part B: 200 kilogram per drums.
Custom package available at additional charge.
 
Notes
1. Qtech product is intended for industrial use by properly trained professional applicators only.
2. Thoroughly mix container of B component with an air-driven power mixer for a minimum of 15 minutes prior to application.
3. Adding a nitrogen blanket is strongly recommended for use on the "A" component for storage after opening.
4. It is a 100% solids production, strictly prohibit add any diluents.
5. The quality and fitness of the product is depending upon the proper mixture and application of the component by the applicator.
6.This specification is an accumulation of long term testing and experience. Published technical data and instructions are subject to change without notice.
7.  For more information please consult the Qingdao Shamu International Trade Co., Ltd. or visit our website www.shamu-intl.com or www.polyurea.cn.
 
Technical Data Sheets
    • Qtech-407 Anti-Microbial Polyurea Material  [2011-05-06]
 
APPLICATION INFORMATION
    • APPLICATION INFORMATION  [2011-05-06]
 
CHEMICAL TEST DATE
    • CHEMICAL TEST DATE  [2011-05-06]